CART (0)
$0.00
Truflo - Pulsepro Pulsation Dampener Series
The cable plug Type 2509 is used to connect devices and components, especially solenoid valves with plugpin assignment A according to ISO 4400.
Burkert Type KK02 5M Cable with Sub-D socket, 25 pin
Burkert Type SET3 - Wearing part set
Type SET6 - Valve & plug sets
Installation of a calibration cylinder on the suction side of your LMI pump simplifies calibration.
This molded polypropylene wall mount bracket is rugged and chemically resistant.
Maltz Sales Company provides pH buffers as pre-mixed, ready-to-use, color-coded liquids: red (pH4.01), yellow (pH7.00) and blue (pH 10.00).
The PC Series is a dual regulated power supply is designed for applications in which a magmeter is used together with a 4-20 mA transmitter such as the AO55 or FT440. Although a single 24 VDC power supply can be used, there is a risk of a ground loop interfering with proper operation of the 4 20 mA current loop. This risk is eliminated by the dual power supply.
The RSP5 solar panel makes it possible to use Seametrics flowmeters in remote applications where a reliable source of electricity is not available or practical. The RSP5 is intended for use with a standard 12V, 22-33 Amp-hour Sealed Lead Acid battery (not included). It comes standard with a charge controller and corrosion resistant mounting hardware. The RSP5 can also be used to provide up to a 40-day back-up power supply for periods of darkness.
SeaMetrics - Saddle Accessory
SeaMetrics - Tees Accessory
SeaMetrics - Weld/Braze Accessory
Sensorex's Calomel Free pH electrodes! The performance of a Calomel electrode is now available without the hazardous Mercury associated with the design. The "Calomel Free" design features an Ag/AgCl based double junction reference with a unique silver ion trap acting as a third junction to impede any silver ion contact with the sample. Reference output is adjusted to deliver the same output as a Calomel electrode using a silver chloride reference.
The Sensorex Electrode adapter, retrofits S8000 to old S653 cable.
Electrode Mounting Gland
The Sensorex BV-1 full port 1” CPVC ball valve is designed for use with our S675 Series Wet Tap Insertion Assemblies and S656CD pH Sensors.
Sensorex's Calibration Box is used to calibrate modbus sensors. The wires from the sensors connect to the terminal block on the front of the box. It connects to a computer via a USB interface.
The Sensorex pH and ORP buffer sachet pillows offer an excellent alternative to pre-mixed buffer calibration standards.
The Sensorex S853 is a shielded, low-noise, 20-foot cable assembly for our S8000 series pH and ORP sensors. This cable assembly has 3/4″ NPT thread for inline or submersion installations.
The Sensorex S853 is a shielded, low-noise, 25-foot cable assembly for our S8000 series pH and ORP sensors. This cable assembly has 3/4″ NPT thread for inline or submersion installations.
The Sensorex S653/20/BNC has a 20' cable and BNC connector. Submersible Combination Electrodes are mounted in the Threaded Cable Cap Assembly.
The Sensorex S653/20/BNC has a 25' cable and BNC connector. Submersible Combination Electrodes are mounted in the Threaded Cable Cap Assembly.
The Sensorex Electrode adapter, submersion mount, no temperature compensation. Use with cable S853.
S8000, ATC Sensor Holder, TC=P1K
S8000, Unity Gain Amplifier (pH Amp) - battery-powered.
Sigmamotor back pressure valves prevent siphoning and varying rates of dosage from fluctuating downstream pressure by enacting positive discharge pressure in your metering pump system.
Sigmamotor Calibration Cylinders will enhance your feed systems by allowing verification of the flow rate of the feed pump.
The CVS 4200 Indoor Stationary Sampler is designed to take samples reliably for years and years.
Walchem 3/4" In-Line Mounting Tee
Walchem Orifice Union, 3⁄4", with 4 Orifice plates, 0-1000 psi. Orifice Unions offer back pressure and flow control, limited by the available orifice sizes. Each union is supplied with four plates.
Walchem Probe Tee, 3/4" NPTF, Low Pressure contacting conductivity, pH/ORP
Walchem Solenoid Valve, Cooling Tower, 3/4" , 120V
Walchem 4-Pin Connector Assembly
Walchem 5-Pin Connector Assembly
Provide positive discharge pressure to stabilize pump output and prevent syphoning.
The new Auto Degassing Valve greatly improves the degassing capabilities of the E-Series metering pumps. The new design uses a dual check valve system to maintain proper pump operation to vent gas out the valve and back to the supply source.
The Walchem Calibration Columns provide verification of metering pump output. Constructed from clear PVC, Glass, or PP with graduations in milliliters and GPH.
Walchem's flow control valves will fine tune the blow down flow rate of your boiler.
Walchem flow switch manifold, low pressure contacting conductivity with 20 foot cable
Provides low cost flow verification on the suction side of E-Series pumps
Walchem Fluent is a cloud-based, water treatment management software tool that amplifies the value of Walchem controllers that have Internet access.
Walchem in-line mounting nut for low pressure sensor mounting or WEL electrode mounting
The Walchem level switch will provide simple low tank level input for controllers and solenoid metering pumps.