Water Analytics salt bridge kit (3 pack) for -R8 series sensors
Water Analytics salt bridge kit (3 pack) for -R5 series sensors
Water Analytics salt bridge kit (3 pack) for -C6/7 series sensors
Water Analytics pH 7 buffer solution, 500mL (1 pint)
Water Analytics pH 4 buffer solution, 500mL (1 pint)
Water Analytics pH 10 buffer solution, 500mL (1 pint)
Water Analytics 600 mV ORP buffer solution, 500 mL (1 pint)
Water Analytics 200 mV ORP buffer solution, 500 mL (1 pint)
W600 sensor input board
Walchem's WEL Series electrodes are cost-effective differential pH and ORP electrodes for industrial applications. They are modular in design with a rugged CPVC housing that contains the electronics; pH and ORP cartridges can easily be connected or replaced in minutes without tools.
Walchem Preamplifier Housing, pH/ORP, ATC, 20 ft. cable, with WEL sensor
Walchem's preamplifier is a watertight method to extend the cable of any conventional combination pH/ORP electrode as far as 1000 feet (305 meters).
Walchem's feed verification has never been better! The PosiFlow® Sensor will verify that your metering pump is truly moving liquid into the system and has not lost prime.
WFP Flowmeters are impeller-type insertion meters designed for use in pipe sizes from ½" to 6".
Walchem orifice unions - back pressure and flow control for your boiler.
Walchem O-ring, FKM, for low pressure sensor mounting
Motorized blowdown valves are opened and closed by your Walchem boiler controller to maintain your conductivity set point.
Walchem Membrane Cap, 20 ppm Free Chlorine/Bromine (Extended pH range) and 20 ppm Total Chlorine
The Walchem level switch will provide simple low tank level input for controllers and solenoid metering pumps.
Walchem in-line mounting nut for low pressure sensor mounting or WEL electrode mounting
Provides low cost flow verification on the suction side of E-Series pumps
Walchem flow switch manifold, low pressure contacting conductivity with 20 foot cable
Walchem's flow control valves will fine tune the blow down flow rate of your boiler.
The Walchem Calibration Columns provide verification of metering pump output. Constructed from clear PVC, Glass, or PP with graduations in milliliters and GPH.
The new Auto Degassing Valve greatly improves the degassing capabilities of the E-Series metering pumps. The new design uses a dual check valve system to maintain proper pump operation to vent gas out the valve and back to the supply source.
Provide positive discharge pressure to stabilize pump output and prevent syphoning.
Walchem 5-Pin Connector Assembly
Walchem 4-Pin Connector Assembly
Walchem Solenoid Valve, Cooling Tower, 3/4" , 120V
Walchem Probe Tee, 3/4" NPTF, Low Pressure contacting conductivity, pH/ORP
Walchem Orifice Union, 3⁄4", with 4 Orifice plates, 0-1000 psi. Orifice Unions offer back pressure and flow control, limited by the available orifice sizes. Each union is supplied with four plates.
Walchem 3/4" In-Line Mounting Tee
The CVS 4200 Indoor Stationary Sampler is designed to take samples reliably for years and years.
Sigmamotor Calibration Cylinders will enhance your feed systems by allowing verification of the flow rate of the feed pump.
Sigmamotor back pressure valves prevent siphoning and varying rates of dosage from fluctuating downstream pressure by enacting positive discharge pressure in your metering pump system.
S8000, Unity Gain Amplifier (pH Amp) - battery-powered.
S8000, ATC Sensor Holder, TC=P1K
The Sensorex Electrode adapter, submersion mount, no temperature compensation. Use with cable S853.
The Sensorex S653/20/BNC has a 25' cable and BNC connector. Submersible Combination Electrodes are mounted in the Threaded Cable Cap Assembly.
The Sensorex S653/20/BNC has a 20' cable and BNC connector. Submersible Combination Electrodes are mounted in the Threaded Cable Cap Assembly.
The Sensorex S853 is a shielded, low-noise, 25-foot cable assembly for our S8000 series pH and ORP sensors. This cable assembly has 3/4″ NPT thread for inline or submersion installations.
The Sensorex S853 is a shielded, low-noise, 20-foot cable assembly for our S8000 series
pH and ORP sensors. This cable assembly has 3/4″ NPT thread for inline
or submersion installations.
The Sensorex pH and ORP buffer sachet pillows offer an excellent alternative to pre-mixed buffer calibration standards.
The Sensorex BV-1 full port 1” CPVC ball valve is designed for use with our S675 Series Wet Tap Insertion Assemblies and S656CD pH Sensors.
Forgot your password?
Thank you for contacting us!
Your message has been sent and someone will be contacting you shortly.
In the meantime, if you have any questions please feel free to call us at 800.370.0439.
The Maltz Sales Team