CART (0)
$0.00
The Sensorex BV-1 full port 1” CPVC ball valve is designed for use with our S675 Series Wet Tap Insertion Assemblies and S656CD pH Sensors.
The Sensorex Electrode adapter, retrofits S8000 to old S653 cable.
The Sensorex Electrode adapter, submersion mount, no temperature compensation. Use with cable S853.
S8000, ATC Sensor Holder, TC=P1K
S8000, Unity Gain Amplifier (pH Amp) - battery-powered.
Electrode Mounting Gland
The Sensorex S653/20/BNC has a 20' cable and BNC connector. Submersible Combination Electrodes are mounted in the Threaded Cable Cap Assembly.
The Sensorex S653/20/BNC has a 25' cable and BNC connector. Submersible Combination Electrodes are mounted in the Threaded Cable Cap Assembly.
The Sensorex S853 is a shielded, low-noise, 20-foot cable assembly for our S8000 series pH and ORP sensors. This cable assembly has 3/4″ NPT thread for inline or submersion installations.
The Sensorex S853 is a shielded, low-noise, 25-foot cable assembly for our S8000 series pH and ORP sensors. This cable assembly has 3/4″ NPT thread for inline or submersion installations.
Water Analytics pH 4 buffer solution, 500mL (1 pint)
Water Analytics pH 7 buffer solution, 500mL (1 pint)
Water Analytics pH 10 buffer solution, 500mL (1 pint)
Water Analytics 200 mV ORP buffer solution, 500 mL (1 pint)
Water Analytics 600 mV ORP buffer solution, 500 mL (1 pint)
Walchem Preamplifier Housing, pH/ORP, ATC, 20 ft. cable, with WEL sensor
Walchem Probe Tee, 3/4" NPTF, Low Pressure contacting conductivity, pH/ORP
Walchem Membrane Cap, 20 ppm Free Chlorine/Bromine (Extended pH range) and 20 ppm Total Chlorine
Walchem 4-Pin Connector Assembly
Walchem Orifice Union, 3⁄4", with 4 Orifice plates, 0-1000 psi. Orifice Unions offer back pressure and flow control, limited by the available orifice sizes. Each union is supplied with four plates.
Walchem in-line mounting nut for low pressure sensor mounting or WEL electrode mounting
Walchem O-ring, FKM, for low pressure sensor mounting
Walchem's WEL Series electrodes are cost-effective differential pH and ORP electrodes for industrial applications. They are modular in design with a rugged CPVC housing that contains the electronics; pH and ORP cartridges can easily be connected or replaced in minutes without tools.
Walchem flow switch manifold, low pressure contacting conductivity with 20 foot cable
Walchem 3/4" In-Line Mounting Tee
W600 sensor input board
Installation of a calibration cylinder on the suction side of your LMI pump simplifies calibration.
This molded polypropylene wall mount bracket is rugged and chemically resistant.
Maltz Sales Company provides pH buffers as pre-mixed, ready-to-use, color-coded liquids: red (pH4.01), yellow (pH7.00) and blue (pH 10.00).
The Sensorex pH and ORP buffer sachet pillows offer an excellent alternative to pre-mixed buffer calibration standards.
Sigmamotor back pressure valves prevent siphoning and varying rates of dosage from fluctuating downstream pressure by enacting positive discharge pressure in your metering pump system.
Sigmamotor Calibration Cylinders will enhance your feed systems by allowing verification of the flow rate of the feed pump.
The CVS 4200 Indoor Stationary Sampler is designed to take samples reliably for years and years.
Truflo - Pulsepro Pulsation Dampener Series
The new Auto Degassing Valve greatly improves the degassing capabilities of the E-Series metering pumps. The new design uses a dual check valve system to maintain proper pump operation to vent gas out the valve and back to the supply source.
Provide positive discharge pressure to stabilize pump output and prevent syphoning.
The Walchem Calibration Columns provide verification of metering pump output. Constructed from clear PVC, Glass, or PP with graduations in milliliters and GPH.
Walchem's flow control valves will fine tune the blow down flow rate of your boiler.
Provides low cost flow verification on the suction side of E-Series pumps
The Walchem level switch will provide simple low tank level input for controllers and solenoid metering pumps.
Motorized blowdown valves are opened and closed by your Walchem boiler controller to maintain your conductivity set point.
Walchem orifice unions - back pressure and flow control for your boiler.
WFP Flowmeters are impeller-type insertion meters designed for use in pipe sizes from ½" to 6".
Walchem's feed verification has never been better! The PosiFlow® Sensor will verify that your metering pump is truly moving liquid into the system and has not lost prime.